Гидрораспределитель 2982877 для мини-экскаватора Caterpillar 306D

306D Control Valve Assy for CAT Excavator spare parts 2982877 Hydraulic Main Valve Aftermarket

Product Overview

The CAT 306D is the 6‑ton step above Caterpillar's micro range — a machine that still fits tight urban sites but carries enough weight and reach to handle real trenching, drainage and foundation work. Its hydraulic main valve, referenced as 2982877, is the distributor that takes pump flow and meters it to boom, arm, bucket, swing and tracks. On a machine this size, the operator relies on the valve for both power and finesse: enough flow to break ground, enough control to work beside a live service.

On a worked 306D, valve wear usually follows a failed repair rather than sudden failure — a rebuilt block that never quite held, a machine that has been "adjusted" a few times, a slow decline in behaviour. The boom drifts down while holding a bucket, the swing overshoots and hunts, the tracks surge when an attachment is cycled. Inside the block, worn spools and scored bores are bleeding oil across circuits. This aftermarket main valve replaces the whole assembly with fresh internals, set to the correct Caterpillar pressures, so the old block comes off and the new one bolts straight back on.

Core Advantages

1. A clean start after a questionable rebuild
If the old block has been re‑spooled and "adjusted" more than once, the reliable move is a fresh assembly. This valve starts with new internals and a bench‑verified pressure setup, not history.

2. Power and finesse in the same machine
The 306D works between breaking ground and feathering beside services. Lapped spools restore both — enough flow for real digging and the control for fine placement.

3. The boom holds position through an idle
Drift under a held bucket is oil escaping past worn spool lands. Fresh spool‑and‑bore pairs hold pressure, so the bucket does not sink while the operator checks the grade.

4. Swing that does not overshoot the mark
Scored bores make the house unpredictable — overshoot, then a hunt back. New internals restore clean metering, so the operator can place the bucket precisely without corrections.

5. A tested block instead of more bench work
Swapping in this complete, bench‑tested assembly is one clean exchange with the same hose positions — the practical choice when the old block has already been rebuilt once.

Manufacturing & Quality Control

Spool and bore pairs are finished to close clearance and run‑in on the bench to confirm free movement without stick‑slip. Each completed valve is flow‑tested across its circuits, with relief and compensator settings logged before acceptance; anything off spec is stripped and reworked. The finished block is oil‑fogged, port‑plugged and shipped on compact cushioned packing.

Frequently Asked Questions

Q1: How do I confirm 2982877 matches my 306D?
A: Send the machine serial number and a photo of the old valve's tag. CAT build variants across the 306D run can differ, so we confirm before dispatch.

Q2: What symptoms indicate a worn main valve?
A: Boom drift under load, swing overshoot with hunting, tracks that surge when attachments are cycled, and a machine that has lost its fine control. A leak test will confirm before you commit.

Q3: Is a repair kit a better option than replacement?
A: If the block casting is sound and it has not been rebuilt before, a re‑spool kit can work. If it has already been through a rebuild, replacement is usually the safer cost. Send photos and we will advise.

Q4: What else should be serviced at the same time?
A: The hydraulic oil and filters. Flush the circuit, change the return filter and suction strainer, so the new spools start life in clean oil.

Q5: Can this be shipped by express courier?
A: Yes — a valve this size ships well by air or express, often faster and cheaper than sea freight for a single unit. Tell us the destination and we will quote the fastest option.

Q6: What voids the warranty?
A: Materials and build defects are covered. Damage from contaminated oil, water ingress, a seized spool forced into movement or incorrect pressure adjustment is excluded. Photograph any arrival damage before uncrating.